智能高壓驗電器工作原理：

帶電導體上的電子會轉移到驗電器上，移走帶電導體，驗電器金屬箔繼續張開。

智能高壓驗電器注意事項：

1、使用前根據被驗電設備的額定電壓等級，選擇對應的驗電器；

2、驗電前對驗電器進行自檢試驗。須同時按住自檢開關和觸電探針，驗電指示器發出間歇振蕩聲光訊號，則驗電器性能完好，可進行驗電，此時可將絕緣桿連續伸開，進行驗電操作，手不能過黑色把套，驗電器接觸頭與等級的帶電體接觸，可發出間歇聲光訊號表示有電，否則表示無電；

3、更換電池。在驗電器頭與桿連接處擰開，把驗電器下面與桿連接處的螺絲擰開，可更換電池。本產品在工作后自動關閉，有信號輸入則開啟，無信號便自動關閉，功耗小，不需要常換電池。采用Ag13號氧化銀電池4粒，電壓6V。自檢不能發出聲光訊號時再考慮更換電池；

4、定期做試驗。驗電器在電器設備上驗電時要遵照工作規程。試驗前，應進行外觀檢查。當發現驗電指示器的外殼有缺損，絕緣桿有裂紋等不進行試驗，及時更換。

5、驗電器各部分的連接牢靠；指示器密封完好，表面光滑、平整，指示器上的標志完整；絕緣桿內外表面清潔、光滑，無劃痕等。

6、驗電時，應使用相應等級的驗電器，在裝置接地線或接地刀閘處對各相分別驗電。驗電前應先在有電設備上進行試驗，確證驗電器良好。

7、高壓驗電應戴絕緣手套。驗電器的絕緣桿要伸展開，驗電時手應握在手柄處不得過黑色把套。